External Areas grouting

from 1

Absorptive tile grouts waterproofing

What do we need?

Absorbent grouts in exterior and interior with presence of salts.

How do we do it?

Application of NANOSHIELD W Nanomolecular product for protection of porous surfaces against moisture and salts. NANOSHIELD W is applied for the durable protection of tile grouts, since we reinforce its surface against humidity, moisture, salts and appearance of fungi.

Products used

NANOSHIELD W

VLX 181

Step by step

Step 1: Thoroughly clean the area from dust

stegaopoiish-aporrofitikon-armostokon.1

Step 2: Pour NANOSHIELD W at the area of application

stegaopoiish-aporrofitikon-armostokon.2

Step 3: Spread NANOSHIELD W on the area with a rubber spatula. Leave area for 5 minutes and then remove the material that has not dried

stegaopoiish-aporrofitikon-armostokon.3

Step 4: Clean the area by sweeping with a damp cloth

stegaopoiish-aporrofitikon-armostokon.4

Step 5: After 6-8 hours (depending on climatic conditions), proceed with the permanent cleaning of the surface, by mopping it

stegaopoiish-aporrofitikon-armostokon.5

Products used : Waterproofing Tile Adhesives & Grouts

Pool Grouting

What do we need?

The grouts in a pool are places that are more directly exposed to the hydrostatic pressure of the water and the corrosive action of chlorine.

How do we do it?

The use of two components epoxy grout  FMF 155 gives complete protection over time by the hydrostatic pressure and by the erosive action of chlorine and other chemical agents.

Products used

FMF 155

SEAL POOL

Step by step

  • The application should be performed when the substrate has a humidity content of <4%. The epoxy grout FMF 155 is provided in two components A and B in a predetermined ratio are mixed shortly before use.
  • Pour the entire contents of the B (hardener) into the container A (resin) and mix thoroughly with a low speed drill (300 rpm / min.) for 5 minutes until a homogeneous paste. After mixing, applying the product portions to clean joints (without adhesive or debris) by pulling, using a rubber or metal flexible spatula in a diagonal to the direction of the joints. In this way removed the excess material.
  •  The minimum material remains on the surface, it is emulsified by rubbing with a damp sponge and must be cleaned within 20 min. Using of warm water facilitates cleaning. At high temperatures we clean faster. The grout after clotting, cleaned very difficult, only by mechanical means, so it is necessary to clean the tools immediately after use. After hardening of the material is harmless to health. The product in low temperatures loses its workability and reaction times is bigger. Unlike high temperatures grow the pot life.
  • At points where the tiling comes into contact with other parts of the pool, such as e.g. Lights should be left joint which should be sealed with silicone permanent immersion in water SEAL POOL.

Products used : Tile Adhesives & Grouts Waterproofing

Terrace Grouting

What do we need?

The grouting of the terrace is a fairly demanding application as exposes the paving permanently solar UV radiation and strong climatic variations (frost, heat, rain, etc.).

How do we do it?

The use of two component epoxy grout FMF 155 gives complete protection and durability in the most extreme climatic conditions over time.

Products used

FMF 155

ELASTO-PU

BAKER ROD

Step by step

  • The application should be performed when the substrate has a humidity content of <4%. The epoxy grout FMF 155 is provided in two components A and B in a predetermined ratio are mixed shortly before use.
  • Pour the entire contents of the B (hardener) into the container A (resin) and mix thoroughly with a low speed drill (300 rpm / min.) for 5 minutes until a homogeneous paste.
  • After mixing, applying the product portions to clean joints (without adhesive or debris) by pulling, using a rubber or metal flexible spatula in a diagonal to the direction of the joints. In this way removed the excess material.
  • The minimum material remains on the surface, it is emulsified by rubbing with a damp sponge and must be cleaned within 20 min. Use of warm water facilitates cleaning. At high temperatures we clean faster. The grout after clotting, cleaned very difficult, only by mechanical means, so it is necessary to clean the tools immediately after use. After hardening of the material is harmless to health. The product in low temperatures loses its workability and reaction times is bigger. Unlike high temperatures grow the pot life. Expansion joints must be provided every 25 m2. The relationship between sides should not exceed 1: 2.
  • The joints are filled with use of polyurethane silicone ELASTO-PU and the corresponding string support joint closed cell BAKER ROD.

Products used : Tile Adhesives & Grouts Waterproofing

from 1