Decorative Plasters

from 1

Organic Coatings

What do we need?

We wish to decorate interior and/ or exterior surfaces of buildings without paint requirement.

How do we do it?

The decoration will be done with the application of THRAKON colored organic coatings which will impart color coverings in different styles.

Products used

GLX 494 Prim

DEC 428 Polyplast

DEC 431 Fine

DEC 429 Silicate

DEC 437 Si & Si

DEC 438 Silicone

DEC 428 Polyplast

Step by step

We ensure smooth final surfaces, clean and free from lumps. Large unevenness and cracks in the substrate must be repaired.

Necessary plastered surfaces of components with 3 layers system (spray-basic-final) or 2 layers system (spray – one layer plaster) of THRAKON and let it dry completely. Finally we repair any defects.

Depending on the desired texture of the final surface and the manufacturing requirements choose the corresponding coating (see. decorative coating table):

Before applying the organic plaster surfaces should be primed with the acrylic primer GLX 494 Prim which must be painted in the color of the final coating.

Application of organic topcoat:

First spread on the surface and then the excess material is removed so that the thickness of the layer corresponds to the grain size. Depending on the style of the coating, use stainless steel or plastic spatula.

The coating is applied with a plastic spatula to properly achieve the desired style and avoid any discoloration of the final surface. The application process requires coordinated the workshop mode of the method to be followed “wet-on-wet” without interruption in continuous surfaces. Otherwise if  first coat dries on the surface before and after apply fresh material on the surface following will be noticeable discolorations on splices. Therefore, it must ensure that enough artificial application at every point of the scaffolding and take into account the weather conditions because they affect the drying time of the material.

Note: In cold weather and high humidity, drying time is lengthened while at high temperatures with low humidity the drying time is slowed.

Products used : ETICS & Facade Products

Cementitious Coatings

What do we need?

We wish to decorate interior and/ or exterior surfaces of buildings.

How do we do it?

To remedy the problem, it applies special repair plaster that has adhesion ability to grip in many different structural surfaces and in addition does not crack at the joints, which is common to ordinary plaster.

Products used

GLX 290

DEC 424 SCRATCH

DEC 425 RILLEN

DEC 440 ROLLER

Step by step

We ensure smooth final surfaces, clean and free from lumps.

Necessary plastered surfaces of components with 3 layers system (spray-basic-final) or 2 layers system (spray – one layer plaster) of THRAKON and let it dry completely.

Finally we repair any defects. Depending on the desired texture of the final surface is selected and the appropriate product:

  1. DEC 424 SCRATCH coating will create coverings type «Scratch» while the coating DEC 425 RILLEN will create coverings type «Rillen». First prime with acrylic primer GLX 290. Then spread with a spatula a thin layer of decorative plaster evenly across the surface. With a rubber float, pressing very lightly, originally smooth the surface. Before the plaster even pull with a rubber float, pushing gently format the final surface, making vertical, horizontal or circular movements.
  2. With coating DEC 440 ROLLER we can create many types of decorative surfaces. The surface construction made primarily with roll. Depending on the type of finish choose the appropriate roll type to use. There are rubber roller that give different relief (rillen, thick, thinner, etc.). It can also be used and the roll of relief, or other support surfaces forming tools (sponge, comb, etc.).

Select a part of the surface that will decorate, depending on the available time  so as to prevent to form the finish before the plaster dries. With metal spatula initially apply the plaster DEC 440 ROLLER in a very thin layer (priming) and after pull evenly spread in the selected surface a second layer in thickness 3 – 5 mm.

Smooth the surface with the metal spatula so that no lumps and surplus material. Depending on the type of finish you want to configure let it pull for a while and then with the special roll form the surface. Depending on the speed of the roll, the pressure you apply, and the processing time created different terrain type surfaces. To be able to connect neighboring areas without connections appear, you should not let the plaster pulls completely in an area and continue in the neighboring. If desired the coating of a surface with a relief-type roll, then first add a small amount of water in addition to the material to become more fluid. Then with the relief roll paint the wall creating at will different densities embossed surfaces.

Products used : ETICS & Facade Products

from 1